MDGx MAX Speed WinDOwS
MDGx MAX Speed WinDOwS
OLD Über-Clocked PC Benchmarks
[1999  2001]
    Contents:
2 OVERclock or NOT 2 OVERclock ?!
PROs + CONs
    Overclocking on the Internet:
      Info + Guides:
      Price Search + Vendors:
      Software [free(ware)]:
Back 2 Contents
Hardware Specs + Prices
[1999  2001]
Back 2 Contents
Hardware Settings
[1999  2001]
Back 2 Contents
Software Settings
[1999  2001]
Jump to:
Microsoft Windows 98 SEU (Second Edition Updates) retail CD-ROM [build 4.10.2222 A + MS-DOS 7.10] with ALL up-to-date Patches, Fixes + Updates: Installed
Back 2 Contents
The Benchmarks
[1999  2001]
Jump to:
My system main specs [back in 1999 see my current system specs here]:
All benchmark results below were obtained using these hardware settings:
Testing accuracy:
Windows Benchmarks
DOS Benchmarks
Back 2 Contents
Benchmarks on The Net
Back 2 Contents
CPU Cooling Comments
[2000  2008]
     R. P. Weaver:
"In reviewing your personal PC specifications, I noticed that you were using a heat sink compound (RadioShack). This concept of using a compound is overlooked by many of the individuals that build their own systems, and by most commercial manufacturers.
My tip is to use a thermal compound such as ThreadEasy or its equal, commonly used in the transfer of heat generated by disk brake assemblies, which will transfer heat from your CPU to its heat sink with greater effiency and as a side benefit, it will not dry out in the same manner that the Radio Shack compound does."
     Alan C. Fang:
"Incidentally, I read this one guy's comments on your heat sink grease. I believe heat sink compound does NOT dry out. The best way to get good thermal contact (that I know of) is to have a very thin but complete layer of grease. You can check for a complete layer by spreading a very thin layer on the CPU, and then putting on the heat sink and wiggling it around a bit. Then take off the heat sink and check where you need more grease. To get a thin layer, put the heat sink on the CPU and press down moderately hard and wriggle it around a little bit, until you hear the "tss tss" sound of metal on ceramic."
     Talley Lewis:
"This is just a little note about the guy who said that the thermal grease from good old Radio Shack would dry out. Oh my god so untrue... I applied some of this miracle compound on a 286 a few years ago, then took the heat sink off yesterday and it was still slippery. ;)
I guess people should use something before they comment on it."
     Terry Fugate:
"I am a TV engineer and have worked on a LOT of electronic equipment.
I have found that regardless of the maker of heatsink compound it will all "dry out" if subjected to *enough* heat. TO-220 devices (a common case style) are very prone to this, aggravated by running the device/heatsink at elevated temperatures. The hotter the device the faster the grease will bake out. But this is not something to worry about, as the grease is only there to allow the compound to be spread on the device and heatsink junction.
The white stuff is Zinc Oxide (ZnO) and the effectiveness does not seam to decrease with the grease gone.
On several occasions I cleaned and reapplied new compound after changing one device on a heatsink and found that the new compound did not improve cooling. Unless the junction is disturbed, drying out does not look to be a major problem. It might be an indication that more air flow is needed to keep the CPU/heatsink cooler.
There are other heatsink compounds that are much better at moving heat: see this Overclockers.com page. These guys are serious about cooling! Unless one is overclocking or using an early Cyrix CPU, exotic cooling should not be an issue.
After all, most of us are not going to keep a CPU for (more than) 5 or 10 years.
I like to move lots of air through my PC case. I worry more about heat effecting hard drive life then CPU life. Most cases do not move nearly enough air across the HD/CD/DVD area. And modern video boards can also benefit from better air flow.
I found that by gutting a fan, removing the blade, armature and support arms, and using this to space a fan away from the small inlet vent holes, will reduce fan noise (in my case checked with a Radio Shack Sound Meter) by about 9 dB. That is a big improvement in overall noise level. I am using a large (4.5") fan that was just too noisy for comfort. I sacrificed a dead fan for the project. Smaller fans will experience a similar level of improvement."
 
Back 2 Contents
Street Price Watch
Computers + Electronics | BDs + DVDs
    Computers + Electronics: Computers, computer products + electronics best prices, search engines, vendors + info:
  
    Blu-ray Discs (BDs) + DVDs: Blu-ray Discs (BDs), DVDs, music, books + games best prices, search engines, vendors + info:
Back 2 Contents
Back!
©1996-2023 MDGx (a.k.a. AXCEL216): Everything here is FREEware. Always free of ad(vertisment)s, cookies, tracking, malware + spyware. I have created [August 1996], maintain and update these web pages entirely by hand using Programmer's File Editor [replaced Notepad].
I do not promote, speak in the behalf of, advertise or work for any computing, technology, news or internet profit business. All ©copyrights and ®registered trademarks retain owners' property.
MDGx
MDGx MAX Speed WinDOwS